Just picked up my truck from the shop last night, the first thing that breaks is my drivers seat. Are all the seats interchangable between Bronco Trims within the same generation? Or are there any inexpensive aftermarket alternatives?
Seats ?
Started by
Guest_92BustinBronco_*
, Aug 03 2004 04:55 AM
5 replies to this topic
#2
BK85
-
- Members
-
- 14 posts
Duck Tape L'fixer :)
- Interests:85 XL Full Size, 302FI, 4spd manual, Alloys, 31.5" BFG Long Trails, Westin Step Bars, Front Seats and Console out of an Eddy Bauer, Sounds from a Taurus. 180,000 miles without a rebuild and still kickin.
Posted 03 August 2004 - 06:07 AM
I think all are interchangeable. I have an 85 XL (bottom of the trim line) and I found an 88 Eddy Bauer and the seats bolted right in to my 85. I had to drill holes for the center console and thats all.
BK
BK
#3
Ktomek06
-
- Moderators
-
- 509 posts
F-Series Commander
- Location:Bay City, TX
- Interests:Hunting, Fishing, Lifeguarding, my bronc, and a lot of other stuff.
Posted 03 August 2004 - 06:21 AM
I unbolted the seats a while back to clean up the carpet real good and i believe they are all interchangable..if not make it!
1994 Eddie Bauer Bronco
http://ftw.truckmoxi...ery.ten?id=9316
http://ftw.truckmoxi...ery.ten?id=9316
#4
Justshootme84
-
- Moderators
-
- 914 posts
F-Series Commander
- Location:Palacios, TX
- Interests:4wd trucks, hunting, fishing, music
Posted 03 August 2004 - 06:25 PM
I belive all of the 80-96 F-150 and Broncos share the same bolt pattern for the seat mounts, and even the later-model Explorer seats will fit. If you are lucky enough to find a set in a salvage yard, they will run about $50 per seat.
1984 Bronco XLT, 351W H.O., C-6 AT, Ford 9", SkyJ 6" lift, 35" tires on MT Classic rims, S&W Racecars 10-pt cage kit, custom "shaker" assembly.
1988 Bronco Custom, 302 EFI, C-6 AT, Ford 8.8". parting out
1986 Bronco Custom, 300I-6, NP435
1988 Bronco Custom, 302 EFI, C-6 AT, Ford 8.8". parting out
1986 Bronco Custom, 300I-6, NP435
#5
Guest_Desert Donk_*
Guest_Desert Donk_*
-
- Guest
Posted 03 August 2004 - 09:11 PM
I just bought seats from a guy back east for 100 bucks a seat on Ebay. Plus another 125 for shipping. No way could I find them here in AZ. I think the lack of rot out here in the Arizona desert makes most vehicles well sought after. Not a single one in a junk yard that I could find for YEARS. I looked for 5 years here.
#6
Justshootme84
-
- Moderators
-
- 914 posts
F-Series Commander
- Location:Palacios, TX
- Interests:4wd trucks, hunting, fishing, music
Posted 04 August 2004 - 06:29 PM
Yeah, I think there were four sets of F-150 seats in the whole state of Texas last time I looked for some. Very hard to find. I'm always looking on ebay, too.
1984 Bronco XLT, 351W H.O., C-6 AT, Ford 9", SkyJ 6" lift, 35" tires on MT Classic rims, S&W Racecars 10-pt cage kit, custom "shaker" assembly.
1988 Bronco Custom, 302 EFI, C-6 AT, Ford 8.8". parting out
1986 Bronco Custom, 300I-6, NP435
1988 Bronco Custom, 302 EFI, C-6 AT, Ford 8.8". parting out
1986 Bronco Custom, 300I-6, NP435
Reply to this topic
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
